Having problems with your Air Conditioners ?

Kelvinator fault code e6

\015 Split system A/C fan works but no cooling, showing error code E6.\015

Answers :

Repair Help & Product Troubleshooting for Air Conditioners
You need a second opinion or clarification ? ask it in the comment box OR you can Ask Your Own Question

Tips for a great answer:

  • Please provide as much detail as possible as this will allow our members to better understand and respond to your Comment
  • If you need clarification, ask it in the comment box
  • It's 100% free, no registration required

Suggested Questions/Answers :

It is recommended you read all this kind of situations

Kelvinator fault code e6


... Electrolux Air Conditioners

Kelvinator fault code e6


... Electrolux Air Conditioners

Kelvinator air fault codes - Air Conditioners


... Air Conditioners

Kelvinator split L3 fault code - Air Conditioners


... Air Conditioners

I have a kelvinator kwh35hra room a/c I habe fault code e0


Code E0 Error detail Remotecontrol transmission error (signal receiving error)Inspected unit Remote control ... Air Conditioners

KELVINATOR KSR20C Our split systeme air con does not heat or cool the outside fan run when on but the inside fan doesnt run the little led on the circuit board on the outside unit is blinking on for 3 sec ond off for 3 sec do these air cons have a fault codes ??


One might think so, YES! look on one of the door panels that you can remove! Thank-you-very-much! ... GE Zoneline AZ38H12DAD Split System Air Conditioner

Kelvinator split ac model ksv70hra#1 fault code e1


... Air Conditioners

I ordered a universal remote control for a Kelvinator air conditioner (in Australia) and Kelvinator isnt listed on the code list - hence unable to use the remote and turn the air conditioner on. I have Googled for a Kelvinator code but am unable to find one. Can anyone assist.


... Air Conditioners

I have the error code A77 on my ariston microgenus HE 28 boiler. I have looked at the fault chart and it gives you 3 options but does not tell you how to repair or test any of them. I have empted the condense trap and pushed the reset button but the fault code is still there. any ideas????


... Air Conditioners

Ecu-Maxx Marine Air-Con. Compressor Load Fault Code (CLF) appears. Air Condition turns on but then after 2 minutes, I get the CLF code. Manuarl says it is Compressor Load Fault. How do I fix this?


Clean the filter on the water pump. It may be clogged. Even if there is just a little bit of gunk in there it can cause this error. ... Air Conditioners

Vulcan eco 120 stoped working, checked fault codes and it said hot serface igntier. i changed that and tryed operation, unit still dose not light. when i press reset fault codes say failure to light, but sometims it also says slow closung gas valve. how can i fix it?


... Air Conditioners

PANASONIC CU160C53XP FAULT CODE F33 COMES UP ON KEY PAD WHAT DOES IT MEAN HOW CAN I OBTAIN FAULT CODES FOR THIS UNIT THANK YOU FOR ANY HELP


BEST WAY IS TO GET AHOLD OF THE MFR'S TECH SUPPORT LINE EASILY OBTAINED FROM YOUR SERVICE MANUAL OR INFO (NOT SURE OF STATE) ... Fedders A6P09S2A Air Conditioner

Unit in room displays fault code -0 and 6. Unit is a Sharp eco inverter AY-XP07ER. Unit runs for a few minutes and cuts out showing fault code.


Do not allow the signal receiver window to receive strong direct sunlight, since it can adversely affect its operation. If the signal receiver window is exposed to direct sunlight, close a curtain to block the light.\015\012\015\012Using ... Sharp Air Conditioners

Error code EO fault code


... Air Conditioners

Have a kelvinator split aircon model KSV 26 HRB showing error code E3. It will run and cool for about 20 seconds after the power is switched off and on but will stop showing the above error code. It is out of warranty. Can you tell me what the code means and what it needs to fix it.


... Air Conditioners

F0 Fault Code on a Shinco heat pump. What causes this fault? Is there a service manual or any technical information available to help a trade person correct this fault.


... Air Conditioners

I got a panasonic inverter a/c cs-e12eku with fault code f91and another one with code f90 what are this codes.


... Panasonic Air Conditioners

Where can I get hold of the AMCOR dual split unit (SF15) "F" fault-codes?


They are in the user manual, or on the panel by the control board. ... Air Conditioners

Fault code for Fujitsu split sytem ASTA24LCC


... Fujitsu Air Conditioners

My ariston boiler displays a red light and A01 fault code. It fails to ignite. Sometimes I can press reset and it will light but this is rare and at mostly even the reset won't get it to reignite. The booklet helpfully tells me it is an ignition fault, but what is causing it?


... Air Conditioners

Boiler in Fault with Ionisation fault code. Can I clean the probe?


... Air Conditioners

I have a DeLonghi CF210 and I'm getting the "E3 Fault" code on the main screen. It will not power up in Air Conditioning mode, but the fan mode will run. I saw where someone suggested it is a voltage problem, and have tried it in several outlets to no avail. This problem happened to me about a week ago and I turned it off for a while (10-20 minutes), then turned it back on and it worked again for a week before giving me the E3 Fault error today. I do not have the financial resources to sen


Remote controller comms error. Check wired correctly, if so check dipswitch in RC. Set to Sg for 1 unit, or Gr for group then reset power ... DeLonghi CF210 Portable Air Conditioner

Yonan Split Air Conditioning System is showing a F6 Fault. What is the fault code related to


F6ambient temp.sensor of outdoorfault1?Check whether the resistance of sensor is normal,otherwise replace it.2?Check whether the sensor wire is short circuit or opencircuit, and whether the plug is well ... Air Conditioners

Mitsubishi mr slim mn PUL18EK outdoor, PL18FK2 indoor. Getting Fault code P8. wires connected,correct phasing. OA thermister 4160 ohms. 77deg oa and room temp 77deg F.Large line 62.9 deg F at outdoor unit and small line 49.8 deg F. Unit drawing 6.9 amps...Why is customer getting the P8 failure code?


8 flash is a pipe temperature error. ... Mitsubishi Air Conditioners

Hi its mits FDCVA402HENAR and the fault code shows I/U NO 00 PROTECT STOP can you please tell me the fault thanks SHERBET


... Mitsubishi Air Conditioners

A detailed question is important to get you a relevant answers

  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
all rights reserved to the respective owners || ad-trader.net || Terms of Use || Contact || Privacy Policy
Load time: 0.0455 seconds