Having problems with your Air Conditioners ?

I have an old CW-C60YU model air conditioner which is in one of my walls. How do I remove the chassis in order to check for mold? I have removed the filter as well as several screws but it still does not move. Do you have the original service manual? I do not and it would help.


Answers :

I believer to panasonic does not pull out but you have to take the unit apart by taking it out of the wall and removing a screw on top (or more) and all of the screws around the bottom edge. It has been a number of years since I worked on a panasonic but if there are screws around the bottom this is usually a sign its a cased model and not a slide out. But on the mold if you have any it will be on the inside coil only if you see no visible mold you have none. If you want to kill mold spores mix a 10% solution of bleach in a spray bottle and spray the inside coil with the unit off ketch any drips and then hold a towel ect you dont like over the front and turn on the fan (no need for cool just fan) Shut it off and repeat. Then let it set for 10 min and then spray with clean water just like the bleach but do it 3 times. This will kill any mold in your tray or backside of the coils. I hope this helps just becareful with the bleach it is very uncomfortable in the eyes only happened to me once never again. good luck

Repair Help & Product Troubleshooting for Air Conditioners
You need a second opinion or clarification ? ask it in the comment box OR you can Ask Your Own Question

Tips for a great answer:

  • Please provide as much detail as possible as this will allow our members to better understand and respond to your Comment
  • If you need clarification, ask it in the comment box
  • It's 100% free, no registration required

Suggested Questions/Answers :

It is recommended you read all this kind of situations

I have an old CW-C60YU model air conditioner which is in one of my walls. How do I remove the chassis in order to check for mold? I have removed the filter as well as several screws but it still does not move. Do you have the original service manual? I do not and it would help.


I believer to panasonic does not pull out but you have to take the unit apart by taking it out of the wall and removing a screw on top (or more) and all of the screws around the bottom edge. It has been a number of years since I worked on a panasonic ... Panasonic CW-C60RU Air Conditioner

My Everystar MPM1-10CR-BB6 model air conditioner will not come on. I had removed the cover in order to do a thorough cleaning of the cooling coils (vacuumed off all months of collected dust & dirt). Wne I put the cover back on, the unit would not power on. I removed the cover again and found that I had one of the screws had severed a wire to the control panel (the purple wire that leads to DM3). I spliced the wire and checked for continuity with an ohm meter but... the unit still will not po


I'll pass on the link to the users manual. Hopefully your questions should be present in that manual:http://www.2instructions.com/search.php?creference=D7bffqa2w3....................sodeep ... Danby DPAC8020 Air Conditioner

Our dog chewed through the wires that i believe run to the thermostat, tried to reconnect the wires and still not running, also tried new fuses and still nothing, just wondering if another part needed to be replaced or if chewing through the wires would short out the ac, any advice would help thanks.....


Shorting the wires usually just blows the fuse on the control board in the inside unit. BUT there is a chance the contactor coil was shorted out as well. Will the inside fan come on if placed in the ON position but the system switch in OFF ? If no ... Goodman Air Conditioners

I have a dometic roof top a/c for a travel trailer, model #59516.731G when the relay cuts on to cool it would make a loud buzzing sound but would function the way it should. freezing over sevral times. Untill yeasterday, the relat wont cut on to cool at all now. fan motor on both fan & a/c sides lo,med, hi still work. would this mean the thermostat has gone out? thanks for any and all assistance you can help with charles


... Dometic Rooftop RV Air Conditioner

I have a CGL300TQ ventless propane heater. The thermstat quit working. I have shocked the thermostat bulb several times but it still does not work. The parts list shows part# slt545 or could be slt545 thermostat control vavle which I assume is the problem. I have called charmglow several times but I am told I cannot get this part. I do not understand why I cannot get this part to repair this unit. Can you help me. Thank You,


... Air Conditioners

Everstar model MPM1-10CR-BB6 portable AC no longer blows cool air. I have attempted to drain the unit but no water has come out for several months. I also attempted to press and hold the "turbo" button but still nothing. All the buttons and lights still work on the unit, just no cool air. Please help.


Start checking the small things. Here are the things that you need to check:1. Fuse2. CapacitorBut the most common thing that could cause this problems are, running out of freon and/or leak in the copper tubes. The tubes ... Air Conditioners

My unit is running but not blowing cool air. I went outside and the condenor fan was not moving. Took a stick and shoved a blade and the fan started moving but the air is still not cool inside. I did notice the air coming through the unit outside after fan was blowing was cooler than my 2nd a/c unit that was working fine. I wondered if the entire unit was frozen. I turned off unit at thermostat and figured I would see what happens tomorrow


Sometimes on new units it is common for the fan to not start until you give it a push. Did you happen to hear if the compressor was operating? If the unit was froze-up the Insulated Suction line would also be iced over as well. If it wasn`t it is mor ... Carrier 38CKC024 Air Conditioner

Hello, I have a sanyo ac model # xs3622, c3622 and was wondering if there is a heat setting. I live in a warm climate and have never needed the heat. The remote control has a heat setting but when I change it to heat it still blows cold. Any help would be helpful. Thanks


Your a/c model is only cool, but remote may be heat and cool which normally supplied by all manufacturers. Don't worry. In your remote heat mode will not respond by unit. Helpful advise? ... Sanyo Air Conditioners

I have moved into a house with a Everhot Deluxe 204 wood stove. I have no idea how to use it and I am trying to find a manual for it so we can learn how to use it properly. Would you have a copy of an instruction book that I could have or purchase..? I would appreciate your help...


... Air Conditioners

The motor was making a humming sound, we stuck a screw driver in the unit to get the blades moving again it worked for a minute and now the blades aren't moving and we don't hear the hummming sound, there is still air coming through the vents it just isn't cold


YOUR OUT SIDE CONDENSOR FAN MOTOR HAS WENT BAD ,REMOVE THE OUTSIDE FAN AND MOTOR TAKE WITH YOU FOR A REPLACEMENT MOTOR MAKE SURE THEY MATCHDON'T KNOW WHERE YOU LIVE BUT R.E.MICHAEL CO. IS A GOOD COMPANY ... Air Conditioners

IM PRACTICIN TO GO IN THE FIELD O WIREING AND I WAS WIREING MY GOODMAN CPKE36-1A UP AND IT STILL DOES NT WORK I PUT THE WIRES BY COLOR TOGETHR WITH TO LEFT OVER A GREEN AND A ORAND AND IM NOW AT A STAND STILL I WOULD HAVE A PROFESSIONAL DO IT BUT LIKE I SAID IM N COLLEGE NOW 4 THIS SORT OF STUFF.. JUS NEED A LIL HELP


By reading you post I would sya to hir a professional!!!!! ... Goodman CKL30AR30 Air Conditioner

My unit stopped blowing cold and started blowing hot.i turned off unit looked into furnace and saw pilot was still lit.i put out gas pilot and turned unit back on and it is blowing semi cool air (like fan)but not cool as it should.checked outside ac and it is running....munual says to turn unit off for 2 hrs and if it does not do right then it is compressor.we are currently in the 2 hr process. Any help would be helpful at this point.is there a reset switch or anything I could do to troubleshoo


100 degree temps/high humidity puts an extreme load on air conditioners - but if everything is right with the AC - 'overheating is not a big problem.\015\012\015\012The first thing I would check is whether or not the compressor is running ... Weather King 10AJA4201AH Air Conditioner

Does it hurt anything to draw the cold air from my basement before it goes through my a/c condenser located in my furnace. I would still be using a filter.. Would this process help reduce electrical cost ??


Possibly. Your a/c won't work so hard to remove the heat and you should see the unit run for a bit of a shorter duration. ... Air Conditioners

HAVE A COLEMAN MODEL DRHSO601CB --- THE UNIT WILL RUN FINE FOR SEVERAL HOURS WITH GOOD COOLING AND THEN PERIODICALLY THE TROUBLE LIGHT WILL COME ON THE THERMOSTAT AND THE UNIT HAS SHUT DOWN. TO RESTART - YOU MOVE THE THERMOSTAT TO OFF WAIT 5 MINUTES OR SO AND PUT IT BACK ON COOL -- IT WILL RESTART ALMOST EVERY TIME AND RUN FOR SEVERAL HOURS. IN THE PAST IN THE PAST I REPLACED THE DEFROST CONTROL BOARD BUT WHEN I DID THAT THIS TIME IT STILL SHUTS DOWN - WHAT OTHER PROBLEMS ARE YOU AWARE OF ON TH


You may have a low pressure or high pressure switch tripping out the board as well. You might try cleaning both the indoor (evaporator) coil and the outdoor (condensing) coil. Be sure to turn off the power source before servicing this. ... Coleman Air Conditioners

I hope someone may be able to help me with my CH i have a alpha CD32C the problem is i cannot get the central heating to come on i have hot water but when i turn the dial onto water and heating nothin happens i have reset it still nothin the only light lit is the green hot water works fine would be grateful for any info


... Air Conditioners

I have just purchased a convair climate master cm9rw and we had it set up and running but after about 15 minutes it started continually beeping so we moved it to the centre of the room so it doesn't have anything near it but it is still beeping and no display. Help


... Convair Portable Air Conditioner

Error Message I have a DeLonghi Pinguino PAC L90 portable air contitioner - last night there were thinderstorms and the electricity went out for a second. Now the unit flashes a message "Fsomething (looks like an L with a line through the middle)". I have unplugged the unit for several minutes but the message still flashes when I plug back in. No response when I depress any of the buttons on the unit. Is there a reset button hidden somewhere? Is there a more serious problem? Help!!


It's actually "Ft", which means "Full Tank".  The instruction manual says to drain the internal safety tank through the drain hoses.\015\012\015\012To drain the tank, open the cover on the rear of the appliance.\015\012Pull out the 2 drain ... DeLonghi Pinguino PACL90 Portable Air Conditioner

On my 2004 duo therm rv roof a/c,I turn it on and to listen to it, everything seems fine.But it's not cooling properly.I have changed the filter,went on roof, removed cover,motor and fan are working fine.Cleaned condensor and evaporator coils,still not blowing cold.I can't tell if compressor is coming on or not,[don't know how]. It feels cold to the touch. Any help would be appreciated.Thank you in advance


On the compressor two pipes normaly one must be very cool .and other pipe very hot this means compressor is ok\015\012if not cooling that much means low charge of freon need repair first the leak then recharge with freon. ... Air Conditioners

I have a Sharp CVP12LX Portable Air Conditioner and i runs for 10 mins then compressor shuts down fans still blows but now blows warm air if i reset the plug it will work for 10 mins then does it all over again the unit will cool but it takes almost 10 mins to kick in if it feels like it any help would be welcomed


... Sharp Air Conditioners

Unit digital display powers up like its working but fan and compressor does not start, I replace the capacitor but it still does the same thing. Your assistance would be very helpful. TY


Hi,Are you sure that the outside switch is working. As both Fan and Compressor is not working, Kindly make sure that the Ac is switched on and replace the outside switch.Check the fuses, one may be bad. The compressor needs 220 to run. Di ... Air Conditioners

Air conditioner I have a Honeywell air conditioner unit. For the last several days it has failed to cool down to the temp I set except at night. When I came in this evening it was 87 degrees in the house. I went to the main unit in the garage and flipped the fuse buttons to off and then back on. Then I dd the same at the main fuse box for the house. (Dont ask me why I thought this would help). Now I can't get the unit to turn on at all. Any ideas?


Yes, first turn your thermostat to the off position. Try to reset both fuse boxes again. If the ac comes back on problem solved, if not fuses and or breakers may need to be replaced.\015\012\015\012Let me know if this helps and we can go futher into ... Haier Energy Star ESA3183 Air Conditioner

I have a 1970's MAC-1199 furnace, but it doesn't heat the whole house. My furnace stays on almost constantly. would a blower motor with higher RPM help? We are moving to a new house next year, and can't afford a new furnace now, but my children will not be able to deal with lack of heat.


Usually the furnace is designed to operate on low speed fan since the air weighs less than the cold air in the cooling season. If you have a med-low speed, try that. Also, check the air filter and if you can get to the a-coil, take that cover off and ... Air Conditioners

My coleman Evcon model DGATO70BDC 1994 starts up and then locks out. The pilot lights and then furnace runs for maybe 2-5 minutes and all that is still running is the air chamber fan. I am thinking of just replacing all parts that could be responsible the problem. There's not much there as probably you know. There is no circuit board just basic electronic ignition,relays thermo senors and etc.. Any help would greatly be appreciated. James


Does your furnace have an air flow sensor? Blowing out the lowest tube will sometimes clear it and allow your furnace to operate. Lack of differential pressure across the burner will cause a lockout. ... Air Conditioners

Have a 15 year old Ruud 2.5 ton condenser that broke down (one of 2 units - the other is still working fine0. The furnaces are 4 years old. They are interconnected - not zoned for our 4200 sq. ft. house. Do i need to replace BOTH condensers because of the freon 410 requirement? Also thinking of going to a 3 ton since the upstairs is never very cool when its hot out. Would this help? If we go to 3 ton, do I need to replace the 2.5 that's working at the same time?


I am not sure what you mean by "interconnected". Basic cooling capacity should be figured on 1 ton of cooling per 500 sq. ft. of space. That would be 4 tons per 2000 sq. ft. You currently operate on 5 tons totally. You require 8 tons of cooling. Othe ... Ruud UAKA042 Air Conditioner

I have GE az55h15dabm1 thats makes humming noise....like a siren. Sometime its really louds otherwise it not that loud but still annoying. I have 12 GE PTAC like that but all other are very quiet except this one. IT looks like Fan Motor but i don't know for sure. Any help would be appreciated.


... GE Zoneline AZ38H12DAD Split System Air Conditioner

A detailed question is important to get you a relevant answers

  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
all rights reserved to the respective owners || ad-trader.net || Terms of Use || Contact || Privacy Policy
Load time: 0.0608 seconds